Publications duirng 1982-1985
    Publications in the Year 1982
  1. P.Gopalan, Kishore and E.S.Dwarakadasa,
    Stress corrosion cracking in Al-Zn-Mg alloy by slow strain rate technique
    Trans. Indian Inst. Metals 35 (1982) 13

  2. G.N.K.Iyengar and K.T.Jacob
    Oxidation of alkaline earth sulfides to sulphates: thermodynamic aspects
    Met. Trans. 13B (1982) 387

  3. A.K.Lahiri and H.S.Ray
    Effect of experimental parameters on non-isothermal TG
    Thermochemica Acta 55 (1982) 97

  4. S.T.Lakshmikumar, V.C.Padaki, P.P.Krishnapur, S.V.Subramanyam, R.M.Mallya and E.S.R.Gopal
    Ultrasonic velocities and thermal expansion coefficients of amorphous Se80 Te20 and Se90 Te10 alloys near glass transitions
    J. Mater. Sci. 17 (1982) 183

  5. N.S.Mishra and S.Ranganathan
    Field-ion microscopic study of short range order and micro- domains in nickel-tungsten alloys
    Proc. 29th International Field Emission Symposium (Ed.) H. Norden, Almqvist & Wiksell International Stockholm (1982)

  6. K.Mohammed Jasim and E.S.Dwarakadasa
    Studies of dry sliding wear in an Al-22% Si alloy
    Wear 82 (1982) 377

  7. G.S.Murthy and D.H.Sastry
    Impression creep of zinc and the rate controlling dislocation mechanism in plastic flow at high temperatures
    Phys. Stat.Sol (a) 70 (1982) 63

  8. B.N.Pramila Bai, E.S.Dwarakadasa and S.K.Biswas
    Scanning electron microscopy studies of wear in LM13 and LM-13 graphite particulate composites
    Wear 76 (1982) 211

  9. R.C.Prasad, E.S.Dwarakadasa and K.I.Vasu
    Effects of mechanical and environmental variables on corrosion fatigue crack growth behaviour
    Trans. Indian Inst. Metals 35 (1982) 6

  10. Pushpalatha C.Bhat, N.G.Puttaswamy and R.M.Mallya
    Mossbauer studies of the corrosion products of cast iron in aqueous ammonium nitrate solution
    Radiochem. Radio and Letters 52 (1982) 299

  11. P.Sastri, P.K.Rohatgi and G.N.K.Iyengar
    Energy analysis of aluminium extraction in India: Part I: Energy consumption patterns
    Trans. Indian Inst. Metals 35 (1982) 552

  12. P.Sastri, P.K.Rohatgi and G.N.K.Iyengar
    Energy analysis of aluminium extraction in India: Part II: Alternate route to aluminium
    Trans. Indian Inst. Metals 35 (1982) 558

  13. P.Sastri, P.K.Rohatgi and G.N.K.Iyengar
    Energy analysis of aluminium extraction in India: Part III: Importance of recycling
    Trans. Indian Inst. Metals 35 (1982) 564

  14. S.D.Sastry, P.K.Rohatgi, K.P.Abraham and Y.V.R.K.Prasad
    Influence of heat treatment on the strength and fracture behaviour of Fe- 12-Cr-6Al ferritic stainless steel
    J. Mater. Sci. 17 (1982) 3009

  15. G.Sambasiva Rao and Y.V.R.K.Prasad
    Grain boundary strengthening and fracture in strongly textured magnesium produced by hot rolling
    Met. Trans. 13A (1982) 2219

  16. G.Sambasiva Rao and Y.V.R.K.Prasad
    Texture and grain boundary strengthening in hot rolled magensium - 12.5 at. % lithium alloy
    Z. Metallkunde 73 (1982) 760

  17. D.Seetharamacharyulu, V.R.Pai Verneker and R.M.Mallya
    Defect sensitization of combustion and thermal decomposition of ammonium perchlorate. Effect of pelletizing pressure and dwell time
    Comb. Sci. Tech. 28 (1982) 41

  18. J.Singh and S.Ranganathan
    On the mechanism of f.c.c. - h.c.p transformation
    Phys. Stat. Sol. (a) 73 (1982) 243

  19. A.H.Yegneswaran, K.S.Raman and Y.V.R.K.Prasad
    Texture strengthening in warm-rolled cadmium-1% silver alloy
    Phil. Mag. A 46 (1982) 507

    Publications in the Year 1983
  20. Ja'afar Hadi Abboud and E.S.Dwarakadasa
    Modification of the spinodal hardening in a Cu-9Ni-6Sn alloy by 0.1% Si or Al addition
    J. Mater. Sci. Letters 2 (1983) 233

  21. J.H.Abboud and E.S.Dwarakadasa
    Effect of 0.1% Si or Al addition on the hardening due to spinodal decomposition in Cu-9Ni-6Sn alloy
    Engg. and Technol. Baghdad 1 (1983) 64

  22. K.Anand and Kishore
    On the wear of aluminium-corundum composites
    Wear 85 (1983) 163

  23. V. Bankaruswamy and Kishore
    Wear of grey cast iron
    Wear 85 (1983) 173

  24. P.C.Bhat, M.P.Sathyanarayana, N.G.Puttaswamy and R.M.Mallya
    Mossbauer studies of the corrosion products of iron formed in aqueous ammonium nitrate solution
    Corrosion Science 23 (1983) 733

  25. M.V.Bhat and K.I.Vasu
    Relevance of microstructure to stress corrosion cracking in Al-5 Zn and Al-5 Cu alloys containing titanium
    Prakt. Metal. 20 (1983) 130

  26. M.V.Bhat and K.I.Vasu
    Strain rate sensitivity of stress corrosion cracking in Al-5 Cu and Al-5 Zn alloys containing titanium
    Trans. Indian Inst. Metals 36 (1983) 101

  27. M.V.Bhat and K.I.Vasu
    Electrochemical aspects of stress corrosion cracking in Al-5 % Zn and Al-5 % Cu alloys containing added titanium
    J. Electrochem. Soc. India 32 (1983) 101

  28. D.Bhogeswara Rao, K.T.Jacob and H.G.Nelson
    Corrosion of 310 stainless steel in H2-H2O-H2S gas mixturs: Studies at constatnt temperature and fixed oxygen potential
    Met. Trans. 14A (1983) 295

  29. P.N.Girijashankar and K.I.Vasu
    Benzotriazole as inhibitor of corrosion of mild steel in sulphuric acid
    J. Electrochem. Soc. India 32 (1983) 47

  30. P.N.Girijashankar, B.V.Narayana and K.I.Vasu
    Metallic pollutants
    J. Electrochem. Soc. India 32 (1983) 86

  31. M.S.Gopalakrishnan, K.S.Raman, S.Vaideswaran and M.R.Seshadri
    New filler materials for manual metal arc welding of spheroidal graphite and malleable irons
    Indian Welding J. (1983) 1

  32. P.Gopalan, T.S.Panchapagesan, Kishore and E.S.Dwarakadasa
    Stress corrosion cracking of aged Al-5Zn-4Mg alloy in 3.5% NaCl solution
    J. Electrochem. Soc. India 32 (1983) 17

  33. Gouthama and Kishore
    Electron microscopic studies on the effect of tin addition on the aging characteristics of Al-0.7Mg2Si alloy
    Bull. Mater. Sci. 5 (1982) 61

  34. Gouthama and Kishore
    Di-isothermal aging of Al-Mg-Si alloy: Effect of tin addition on the clustering kinetics
    Trans. Indian Inst. Metals 36 (1983) 282

  35. M.S.Hegde, T.S.Sampath Kumar and R.M.Mallya
    A study of surface segregation and oxidation of Cu-Mn alloys by x-ray photoelectron and Auger spectroscopy
    Appl. Surf. Sci. 17 (1983) 97

  36. N.Izzat, E.S.Dwarakadasa, S.K.Goel and A.R.Ismail
    SEM studies of fracture in an Al-Al2O3-MgO cast particle composites
    J. Mater. Sci. Letters 2 (1983) 750

  37. K.T.Jacob
    Decomposition of -alumina in an oxygen potential gradient
    J. Appl. Electrochem. 13 (1983) 469

  38. K.T.Jacob and M.Iwase
    Effect of pressure on the e.m.f. of solid state cells
    High Temp. Sci. 16 (1983) 123

  39. N.K.Jain, C.G.K.Nair, K.P.Abraham and Y.V.R.K.Prasad
    Hot workability and kinetics of hot deformation in electroslag refined heat resistant aluminium alloy
    Z. Metallkde. 74 (1983) 633

  40. N.K.Jain, C.G.K.Nair, K.P.Abraham and Y.V.R.K.Prasad
    High temperature deformation of ESR En 36 steel
    Metals Technol. 10 (1983) 1

  41. E.Jiran and K.T.Jacob
    Computation of thermodynamic properties of quaternary and higher order systems from binary data using shortest distance composition paths
    Calphad 1 (1983) 41

  42. A.S.W.Kurny, M.Mohan Rao and R.M.Mallya
    Nitriding of steels - An overview
    Tool and Alloy Steels 17 (1989) 333

  43. F.K.Legoues, K.Chattopadhyay and H.I.Aaronson
    On the application of orientation relationship measurements to distinguish between different nucleation mechanisms
    Scripta Met. 17 (1983) 675

  44. R.Mohan, Kishore, M.K.Sridhar and R.M.V.G.K.Rao
    strength of jute-glass hybrid fibre composites
    J.Mater. Sci. 2 (1983) 99

  45. S.Narayanan, N.Raghunathan, U.B.Nayak and A.K.Lahiri
    Enviromental effects on grinding
    Int. J. Mineral Processing 10 (1983) 309


  46. K.A.Natarajan and I.Iwasaki
    Environmental leaching behaviour of copper-nickel bearing Duluth gabbro and flotation tailing
    Hydrometallugy 10 (1983) 329

  47. K.A.Natarajan and I.Iwasaki
    Role of galvanic interactions in the bio-leaching of Duluth gabbro copper- nickel sulfides
    Separation Sci. Technol. 18 (1983) 1095

  48. K.A.Natarajan, I.Iwasaki and K.J.Reid
    Some aspects of microbe-mineral interactions of interest to Duluth gabbro copper- nickel sulfides
    Progr. biohydromet., Cagliari, May (1983) 169

  49. S.N.Ojha, K.Chattopadhyay and P.Ramachandrarao
    Microstructural and mechanical properties of Al-CuAl2 eutectic alloys solidified over a heat pipe
    J. Mater. Sci. 18 (1983) 1174

  50. M.P.Ramani, Sathyavathiamma, N.G.Puttaswamy and R.M.Mallya @3 = Mossabauer effect study of the thermal decomposition in hydrogen of homogeneously mixed ferrous nickel oxalate with different iron to nickel ratios
    Phys. Stat. Sol. (a) 77 (1983) 87

  51. M.P.Ramani, Sathyavathiamma, N.G., Puttaswamy and R.M.Mallya @3 = Mossabauer effect sutides of the thermal decomposition of iron (11) oxalate in hydrogen
    Materials Chemistry and Phys. 9 (1983) 539

  52. R.Ramesh, Kishore and R.M.V.G.K.Rao
    Dry wear studies on glass-fibre-reinforced epoxy composites
    Wear 89 (1983) 131

  53. K.P.Rao, S.M.Doraivelu, H.Md.Roshan and Y.V.RK.Prasad
    Deformation processing of an aluminium alloy containing particles :Studies on Al- 5%Si alloy 4043
    Met. Trans. A 14 (1983) 1671

  54. G.Sambasiva Rao and Y.V.R.K.Prasad
    Effect of texture and grain size on the fracture behaviour of hot rolled Mg, Mg-12.5% Li and Mg-5% Ti alloy
    Res. Mechanica 9 (1983) 41

  55. G.Sambasiva Rao and Y.V.R.K.Prasad
    Strengthening mechanisms in hot-rolled magnesium and magnesium alloys
    Mater. Letters 1 (1983) 171

  56. G.Sambasiva Rao and Y.V.R.K.Prasad
    Contribution of texture to the strengthening and fracture in hot-rolled magnesium-12.7 at % cadmium alloy
    J. Mat. Sci. 18 (1983) 2385

  57. G.Sambasiva Rao and Y.V.R.K.Prasad
    Changes in texture and grain size in hot rolled magnesium and effect of yield strength
    Bull. Mater. Sci. 5 (1983) 459

  58. G.Sambasiva Rao and Y.V.R.K.Prasad
    Grain boundary strengthening in hot rolled magnesium-5 at% thallium : importance of texture
    Scripta Met. 17 (1983) 147

  59. P.Sastri and A.K.Lahiri
    A central atoms model for binary silicate and aluminate melts
    Phys. Chem. Glasses 24 (1983) 98

  60. M.C.Shaji, B.V.Narayana, N.Manoharan, J.Balachandra and K.I.Vasu
    Hydrometallurgical recovery of copper, lead and zinc from complex sulphide ores
    Trans. Ind. Inst. Metals 36 (1983) 400

  61. K.I.Vasu and Sharath Ahuja
    The aftermath of a high energy society is pollution and the answer is alternate clean energy sources
    J.Electrochem. Soc. India 32 (1983) 77

  62. M.Venkataraman and J.P.Hajra
    Applicability of various formalisms to binary liquid manganese alloys
    Trans. Ind. Inst. Metals 36 (1983) 243

  63. M.Venkataraman and J.P.Hajra
    Thermodynamics of Ni-Mn alloys using oxide and fluoride electrolytes
    Met. Trans. 14A (1983) 2125

  64. Y.Waseda and K.T.Jacob
    Electron charge transfer in liquid copper-tin alloys
    Met. Trans. 14A (1983) 1745

  65. R.S.Yaseen and E.S.Dwarakadasa
    Nature of subsurface damage in a Al-Al3Ni composite material during dry sliding wear
    Wear 84 (1983) 55

  66. R.S.Yaseen and E.S.Dwarakadasa
    Wear of aluminium under dry sliding conditions
    Wear 84 (1983) 375

    Publications in the Year 1984
  67. K.Adam, K.A.Natarajan and I.Iwasaki
    Grinding media wear and its effect on flotation of sulphide minerals
    Int. J. Mineral Processing 12 (1984) 39

  68. D.R.Barker, S.M.Doraivelu, H.L.Gegel, Y.V.R.K.Prasad, J.C.Malas, J.T.Morgan and K.A.Lark
    Computer-aided data aquisition during controlled strain rate upsetting and analysis for metal forming operations
    Proc. North America Manufacturing Research Association, Michigan Technological Univ., USA, (1984)

  69. E.S.Dwarakadasa and C.G.Krishnadas Nair
    An overview of high strength aluminium alloys for aircraft applictions
    Proc. Sem. "High Strength Aluminium Alloys for Defence and Induistry", R.D.E.(Engineers), Pune, Feb. (1984)

  70. G.P.Ghate, K.S.S.Murthy and K.S.Raman
    Effect of tace elements on the delayed artificial aging of Al-7%Si-0.3%Mg alloy
    Aluminium, 60 (1984) E.18

  71. P.Gopalan, Kishore and E.S.Dwarakadasa
    Effect of beryllium additions on the dynamic scc behaviour of heat treated Al-5Zn-4Mg alloy
    Advances in Fracture research, (Eds.) S.R.Valluri, D.M.R.Taplin, P.Rama Rao, J.F.Knott and R.Dubey, Pergamon Press, London, (1984) 2537

  72. P.R.Gopinathachar and U.B.Nayak
    Bulk oil flotation of graphite
    Ind. J. Technol. 22 (1984) 194

  73. M.A.Hussain, E.S.Dwarakadasa and A.R.Ismail
    TEM Study of the structure of very thin anodic oxide films on aluminium
    J. Electrochem. Soc. India 33 (1984) 197

  74. K.T.Jacob, J.P.Hajra and M.Iwase
    Activities of Mn in solid and liquid Fe-Mn alloy
    Arch. Eisenhuttenwesen 55 (1984) 42

  75. N.K.Jain, C.G.Krishnadas Nair, K.P.Abraham and Y.V.R.K.Prasad
    Hot torsional study of electroslag refined RR58
    Trans. Indian Inst. Met. 37 (1984) 493

  76. Kishore
    Some aspects of dislocation precipitate interaction in under- aged aluminium- germanium alloy
    Bull. Mater. Sci. 6 (1984) 1041

  77. K.Mohammed Jasim and E.S.Dwarakadasa
    Wear of aluminium-silicon alloys under dry sliding conditions
    Trans. Indian Inst. Metals 37 (1984) 581

  78. M.Mohan Rao and S.Ranganathan
    Grain boundary diffusion
    Mater. Sci. Forum 1 (1984) 43

  79. J.J.Moore, I.Iwasaki, K.A.Natarajan, R.Peroz and K.Adam
    The effect of grinding ball composition and mineral slurry environment on grinding media wear
    I Mech E.C. 352 (1984) 215

  80. V.S.R.Murthy, Kishore and S.Seshan
    A note on compacted graphite formation
    Scripta Met. 18 (1984) 1219

  81. V.S.R.Murthy, S.Seshan and Kishore
    Surface features of compacted graphite cast iron subjected to wear
    Wear 97 (1984) 199

  82. K.A.Natarajan and I.Iwasaki
    Electrochemical aspects of grinding media-mineral interactions in magnetic ore grinding
    Int. J. Mineral Processing 13 (1984) 53

  83. K.A.Natarajan, S.C.Riemer and I.Iwasaki
    Influence of pyrrhotite on the corrosive wear of grinding balls in magnetite ore grinding
    Int. J. Mineral porcessing 13 (1984) 73

  84. K.A.Natarajan, S.C.Riemer and I.Iwasaki
    Corrosive and erosive wear in magnetite taconite grinding
    Mineral and Metallurgical Processing 1 (1984) 10

  85. B.V.Narayana, M.C.Shaji, S.Balaji and K.I.Vasu
    Aluminium alloys as sacrificial anodes in the cathodic protection of steel
    J. Electrochem. Soc. India 33 (1984) 201

  86. H.S.Prakash and K.I.Vasu
    Materials for sprinkler irrigatiopn system; corosion and other aspects
    J. Electrochem. Soc. India 33 (1984) 57

  87. R.C.Prasad, E.S.Dwarakadasa and K.I.vasu
    Fatigue and corrosion fatigue crack propagation in a high strength aluminium alloy
    Proc. Sem. "High Strength aluminium alloys for Defence and Industry", R.D.E.(Engineers), Pune, Feb. (1984)

  88. Y.V.R.K.Prasad, H.L.Gegel, S.M.Doraivelu, J.C.Malas, J.T.Morgan, K.A.Lark and D.R.Barker
    Modelling of dynamic material behaviour in hot deformation: Forging of Ti- 6242
    Met. Trans. 15A (1984) 1883

  89. Y.V.R.K.Prasad, N.K.Jain and V.V.S.Sarma
    Hot deformation kinetics in rolled versus cast En 36 steel
    Trans. Indian Inst. Metals 37 (1984) 111

  90. Y.V.R.K.Prasad
    Texture dependent mechanical properties of metals and alloys
    Trans. Indian Inst. Metals 37 1984) 399

  91. Y.V.S.S.Prasad, P.Ramachandra Rao and K.Chattopadhyay
    The nature of non-equilibrium solidification of under cooled Ag-Cu alloys in contact with primary dendrites
    Acta Metall. 32 (1984) 1825

  92. M.N.Raghavendra Rao, C.R.L.Murthy, B.Dattaguru and Kishore
    Acousto-ultrasonic evaluation of fibre reinforced plastic components
    Proc. Natl. Conf. on "Non-destructive evaluation", Bangalore (1984)

  93. M.Ramesh Chandra, R.S.Parmar and K.S.Raman
    Mechanical behaviour of PVC welds
    J. Inst. Engr. 64 (1984) 171

  94. S.Ranganathan
    Grain boundary-dislocation interactions
    Bull. Mater. Sci. 6 (1984) 699

  95. S.Ranganathan and S.Banerjee
    Thermal stability
    in metallic glasses (Ed) T.R. Anantharaman Trans. Tech. Publication, Switzerland, 147 (1984)

  96. K.P.Rao and Y.V.R.K.Prasad
    Deformation processing of aluminium alloys 2618 Part I: Kinetics of deformation
    Aluminium 60 (1984) 184

  97. K.P.Rao, H.Md.Roshan, S.M.Doraivelu and Y.V.R.K.Prasad
    Strengthening of high temperature forged 2618 (RR-58) aluminium alloy
    Trans. Ind. Inst. Metals 37 (1984) 465

  98. K.P.Rao, S.M.Doraivelu, H.Md.Roshan and Y.V.R.K.Prasad
    Development of processing map for Al-4Mg alloy
    Trans. Indian Inst. Metals 37 (1984) 471

  99. V.A.Ravi, K.Chattopadhyay, S.Ranganathan, C.R.Prasad and K.Nirmala
    Laser glazing of aluminium alloys
    Proceedings of Third Symposium on Laser and Applications, Tata-McGrawhill, (1984)

  100. A.K.Ray and C.R.Krishnamurthy
    Electrodeposition of copper-tin alloys from a mixed copper sulphate stannous fluoborate bath
    J. Electrochem. Soc. India 33 (1984) 201

  101. G.M.K.Sarma and S.Ranganathan
    Changes in the mechanical properties of -brass during anneal hardening
    Z. Metallkde. 75 (1984) 554

  102. P.Sastri and A.K.Lahiri
    Application of the "Central Atoms" model to alumino silicate melts
    Proc. Second Int. Symp. on Metallurgical Slags and Fluxes, (Eds.) H.A. Fine and D.R. Gaskell (1984) p377

  103. C.Subramanian and Kishore
    Influence of graphite type, modification and hot working on wear of aluminium based particulate composites
    J. Reinforced Plastics and Composites 3 (1984) 278

  104. S.Viswanathan, K.S.Raman. and K.S.S.Murthy
    Effects of process parameters on arc welding of gray cast iron
    Tool and Alloy Steels 18 (1984) 55

  105. Y.Waseda, K.T.Jacob and S.Tamaki
    Current views on microscopic thermodynamics of liquid alloys
    High Temp. Materials and Processes, 6 (1984) 119

    Publications in the Year 1985
  106. K.P.Abraham
    Thermodynamic measurements by gas equilibrium and solid state galvanic cell techniques
    Thermodynamics and Kinetics of Metallurgical Processes, (Eds.) M.Mohan Rao, K.P.Abraham, G.N.K.Iyengar and R.M.Mallya, Indian Inst. Met., Calcutta, (1985) 87

  107. K.Adam, K.A.Natarajan, I.Iwasaki and S.C.Reimer
    Electrochemical aspects of grinding media-mineral interaction in sulfide ore grinding
    Corrosion 85 (1985) Paper No. 362

  108. K.Chattopadhyay
    An electron microscopic study on thin foil intensities of Cu- Zn alloy
    Z. Metallkde. 76 (1985) 496

  109. K.Chattopadhyay
    The role of interfaces in diffusional growth
    Mater. Sci. Forum 3 (1985) 231

  110. K.Chattopadhyay, S.Ranganathan, G.N.Subbanna and N.Thangaraj
    Electron microscopy of quasicrystals in rapidly solidified Al-4%Mn alloy
    Scripta Met. 19 (1985) 767

  111. K.Chattopadhyay, S.Lele, S.Ranganathan, G.N.Subbanna and N.Thangaraj
    Electron microscopy of quasicrystals and related structures
    Current Sci. 54 (1985) 895

  112. K.Chattopadhyay, S.Lele, R.Prasad, S.Ranganathan, G.N.Subbanna and N.Thangaraj
    On the variety of electron diffraction patterns from quasicrystals
    Scripta Met. 19 (1985) 1331

  113. S.M.Doraivelu, J.S.Gunasekara, D.R.Barker, H.L.Gegel, J.C.Malas, Y.V.R.K.Prasad, R.Srinivsan, J.Ramanathan and Chin Li
    Development of an intelligent apprentice system for extrusion die design and process simulation
    Proc. IV Internat. Conf. "Computers in Engineering and Exhibition", MIT, Cambridge, August (1985)

  114. S.Durga and U.B.Nayak
    Beneficiation of low grade flaky graphite from Mavinahalli, Mysore District, Karnataka
    J. Mines, Metals and Fuels, May (1985) 228

  115. Gouthama, G.N.Subbanna and Kishore
    TEM studies on the precipitate morphology in quenched and aged Al-2% Ge alloy
    Mater. Sci. Forum 3 (1985) 261

  116. J.C.Ho, C.E.Oberly, H.L.Gegel, W.T.O'Hara, Y.V.R.K.Prasad and W.M.Griffith
    Composite aluminium conductors for pulsed power applications at hydrogen temperatures
    Proc. V IEEE Pulsed Power Conference, Arlington, June (1985)

  117. J.C.Ho, C.E.Oberly, H.L.Gegel, W.M.Griffith, J.T.Mogan, W.T.O'Hara and Y.V.R.K.Prasad
    A new aluminium base alloy with potentital cryogenic applications
    Proc. Internat. Cryogenic Materials Conf., MIT, Cambridge, August (1985)

  118. I.Iwasaki, S.C.Reimer, J.N.Orlich and K.A.Natarajan
    Corrosive and abrasive wear in ore grinding
    Wear 103 (1985) 253

  119. M.Iwase, K.T.Jacob and E.Ichise
    Mixed ionic and electronic conduction in zirconia
    Proc. Zirconia-83, Adv. Ceramics series, Am. Ceram. Soc., (Eds.) A.H.Heuer, N.Claussen and H.Ruhle, 11 (1985) 182

  120. G.N.K.Iyengar
    Thermodynamics of binary metal oxide solid solutions of AO-BO type
    `Thermodynamics and kinetics of metallurgical processes', (Eds.) M.Mohan Rao, K.P.Abraham, G.N.K.Iyengar and R.M.Mallya, Ind. Inst. Metals, Calcutta, (1985) 35

  121. K.T.Jacob
    Kundsen effusion measurements on Cr-Mn alloys
    Z. Metallkde. 76 (1985) 415

  122. K.T.Jacob and S. Sashidhara Pandit
    Gibbs energy of formation of cobalt di vanadium tetroxide
    J. Solid State Chem. 60 (1985) 237

  123. K.T.Jacob and J.P.Hajra
    Thermodynamic properties and phase boundaries of Co-O solutions
    Z. Metallkde. 76 (1985) 709

  124. K.T.Jacob
    Application of solid state cells to alloy thermodynamics - Critical factors and emerging frontiers
    `Thermodynamics and kinetics of metallurgical processes', (Eds.) M.Mohan Rao, K.P.Abraham, G.N.K.Iyengar and R.M.Mallya, Indian Institute of Metals, Calcutta, (1985) p91

  125. J.M.Juneja, G.N.K.Iyengar and K.P.Abraham
    Measurement of vapour pressure of liquid magnesium by the boiling point method
    Trans. Indian Inst. Metals 38 (1985) 519

  126. R.Krishnamurthy, Kishore and S.Seshan
    Studies on centrifugally cast ductile cast iron
    Fundicao 165 (1985) 12

  127. R.Mohan and Kishore
    Jute-glass sandwich composites
    J. Reinforced Plastics and Composites 4 (1985) 186

  128. V.S.R.Murthy, Kishore and S.Seshan
    Wear behaviour of compacted-graphite cast iron investigated
    Foundry Trade J. 159 (1985) 132

  129. V.S.R.Murthy, Kishore and S.Seshan
    Compacted graphite cast iron - current state of the art
    Sadhana 8 (1985) 361

  130. V.S.R.Murthy, Kishore and S.Seshan
    Properties of cast iron with compacted graphite
    British Foundryman 78 (1985) 71

  131. K.A.Natarajan, S.C.Riemer, I.Iwasaki and K.J.Reid
    Electroleaching studies on selective nickel dissolution from a bulk copper-nickel concentrate Proc. 15th Internat. Mineral Processing Congress, Cannes, France (1985) 413

  132. K.A.Natarajan and I.Iwasaki
    Electrochemical aspects of xanthate and sulfide mineral oxidation by ozone
    Minerals and Metallurgical Processing 2 (1985) 179

  133. K.A.Natarajan and I.Iwasaki
    Decomposition of xanthate collectors with ozone in alkaline solutions
    Minerals and Metallurgical Processing 2 (1985) 241

  134. K.A.Natarajan and I.Iwasak
    Microbe-mineral interactions in the leaching of complex sulphides
    "Microbiological effects of Metallurgical Processes' (Ed.) J.A. Clum and L.A. Hass, TMS, Warrendale (1985)

  135. S.N.Ojha, K.Chattopadhyay and P.Ramachandrarao
    Phase transformation and metastable equilibria in aluminium germanium alloy
    Mater. Sci. Engg. 73 (1985) 177

  136. D.P.Patil and U.B.Nayak
    Selective flotation of scheelite and calcite
    Proc. National Seminar on Mineral Processing Jamshedpur, (1985)

  137. A.Petric and K.T.Jacob
    The Co-Cr-S ternary diagram at 1223 K and applications to the corrosion behaviour of Co-Cr alloys
    Met. Trans. 16 A (1985) 503

  138. R.L.Pozzo, K.A.Natarajan, I.Iwasaki and K.J.Reid
    Electrochemical processing of a complex Cu-Ni sulphide concentrate
    Proc. 15th International Mineral Processing Congress, Cannes, France, 3 (1985) 303

  139. Y.V.R.K.Prasad
    Temperature and strain rate dependence of tensile flow stress in HCP metals; single crystals versus polycrystls
    `Thermodynamics and kinetics of metallurgical processes', (EdS.) M. Mohan Rao, K.P.Abraham, G.N.K.Iyengar and R.M.Mallya, The Indian Institute of Metals, Calcutta, (1985) p345

  140. Y.V.S.S.Prasad, S.L.Agarwal, K.Chattopadhyay and P.Ramachandrarao
    Solidification of undercooled liquid alloys entrapped in solid-A structural investigation
    Proc. V Internat. Conf. `Rapidly Quenched Metals', Wurzburg, Germany (EdS.) S.Steeb and H.Warlimont, Elsevier Science Publishers B.V. Vol. 1 (1985) 39

  141. K.Purushotam Reddy and U.B.Nayak
    Flotation of low grade copper ore from Kallur, Raichur district, Karnataka
    Proc. National Seminar on 'Mineral Processing' Jamshedpur, (1985)

  142. S.Raghavan, G.N.K.Iyengar and K.P.Abraham
    Determination of the thermodynamic properties of MgO-MnO solid solutions by the solid-electroylte galvanic cell technique in the temperature range 1163 to 1318 K
    J. Chem. Thermodynamics 17 (185) 585

  143. V.S.Raja, Kishore and S.Ranganathan
    Thermal and chemical stabilities of Vitrovac 0040
    Proc. V Internat. Conf. 'Rapidly Quenched Metals', Wurzburg, Germany (Ed.) S.Steeb and H.Warlimont, Elserier Science Publishers BV, Vol.II (1985) 1485

  144. V.S.Ramachandra Murthy, S.Seshan and Kishore
    Fractographic features of compacted graphite cast irons failed in impact and tension
    Pract. Met. 22 (1985) 597

  145. Ramani, M.B.Rathnamma, M.P.Satyavathiamma, N.G.Puttaswamy and R.M.Mallya
    Corrosion studies of amorphous Fe39N39Mo4Si6B12
    Proc. 'Solid State Physics Symposium', (DAE) Nagpur, December 1985

  146. Ramani, M.P.Satyavathiamma, N.G.Puttaswamy, A.S.W.Kurny, M.Mohan Rao and R.M.Mallya
    Mossabauer studies of ion-nitrided iron and steel
    Proc. `Solid State Physics Symposium' (DAE), Nagpur, December 1985

  147. Ramani, M.B.Rathnamma, M.P.Sathyavathiamma, N.G.Puttaswamy, R.M.Mallya and P.Chowdhury
    Mossabauer studies of corrosion of metallic glasses Fe81B13.5Si3.5C2 and Fe67Co18B14Si1 in ammonium nitrate solution
    Proc. V Internat. Conf. 'Rapidly Quenched metals', Wurzburg, Germany (Ed.) S. Steeb and H.Warlimont, Elsevier Science Publishers BV. Vol.II (1985) 1489

  148. K.P.Rao and Y.V.R.K.Prasad
    Influence of hard particles pm the safe processing limits to three aluminium alloys
    Aluminium 61 (1985) 844.

  149. A.K.Ray, E.S.Dwarakadasa and K.S.Raman
    The influence of porosity of slag inclusions on properties of Butt welds of 15 CDV6 steel
    Proc. Welding 85, (1985) 11-13-1

  150. T.S. Sampathkumar and M.S. Hegde
    Surface segregation and oxidation studies of Cu-Sn and Cu-Pd alloys by X- ray photoelectron and Auger spectroscopy
    Applications of Surface Science 20 (1985) 290

  151. T.S.Sampathkumar, R.M.Mallya and M.S.Hegde
    Low temperature preparation and characterisation of intermetallics - Fe W, FeMo and some ternary Fe-W-Mo systems
    Bull. Mater. Sci. 7 (1985) 465

  152. P.Sastry and A.K.Lahiri
    Applicability of central atoms models to binary silicate and aluminate melts
    Met.Trans. 16B (1985) 325

  153. D.H.Sastry
    On the dislocation mechanism of plastic flow in metals at high temperatues
    `Thermodynamics and kinetics of metallurgical processes', (Ed.) M.Mohan Rao, K.P.Abraham, G.N.K.Iyengar and R.M.Mallya, The Indian Institute of Metals, Calcutta, (1985) 333

  154. C.Subramanian and Kishore
    Influence of structure on the dry sliding wear of an aluminium alloy
    Proc. Internat. Conf. `Aluminium', New Delhi, (1985) 568

  155. U.Sudarsan, K.Chattopadhyay and Kishore
    Dry sliding wear of Metglas 2605 SC
    Proc. V Internat. Conf. 'Rapidly Quenched Metals', Wurzburg, Germany (Ed.) S.Steeb and H.Warlimont, Elsevier Science Publishers BV, Vol.II (1985) 1439

  156. R.Sundaresan, A.C.Raghuram, R.M.Mallya and K.I.Vasu
    Anomalous diffusion in beta titanium and its effect on sintering
    Sintered Metal Ceramic Composites, (Ed.) G.S.Upadhyaya, Elsevier Science Publishers B.V. Amsterdam, (1985)

  157. C.Suryanarayana and S.Ranganathan
    Amorphous to crystalline phase transformations
    Materials Science Forum 2 (1985) 173

  158. D.Vaman Rao, M.K.Narayana, U.B.Nayak, K.Ananthapadmanabhan and P.Somasundaran
    Flotation of calcareous Mussorie phosphate ore
    Inter. J. Miner. Process. 14 (1985) 57

  159. S.Vasudevan, S.Seshan and K.Chattopadhyay
    A study on the influence of manganese additions on austenitic ductile iron
    British Foundryman 78 (1985) 243

  160. P.Vivekananda, N.S.Lakshmana Rao, B.C.Shyamala Rao and Y.V.R.K.Prasad
    A microjet model of cavitation damage , `Cavitation in hydraulic structures and turbomachinery', (EdS.) R.E.A. Arndt and D.R.Webb, the ASME, New York (1985) 13

  161. K.Vijayaraju, E.S.Dwarakadasa and J.H.Abboud
    SEM studies of fractures in spinodally hardened Cu-9Ni-6Sn-X alloys
    J. Mater. Sci. Letters 4 (1985) 1111

  162. K.Vijayaraju, E.S.Dwarakadasa and Kishore
    Optimisation of mechanical properties through heat treatment in a HSLA steel
    Tool and Alloy Steels 19 (1985) 147